|
Asante
| AsanteFAST 10/100 PCI
| DEC 21140-AE + NS DP83840AVCE + NS DP83223V
| PCI 32/33, 5V
| Fast Ethernet
| TP RJ45: 10Base-T, 100Base-TX
|
Linux 2.4
dmesg
Linux Tulip driver version 0.9.15-pre9 (Nov 6, 2001)
tulip0: EEPROM default media type 10baseT.
tulip0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0) block.
tulip0: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0) block.
tulip0: Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block.
tulip0: Index #3 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block.
tulip0: ***WARNING***: No MII transceiver found!
eth1: Digital DS21140 Tulip rev 34 at 0xdc00, 00:00:94:7A:C2:7B, IRQ 10.
Linux Tulip driver version 0.9.15-pre12 (Aug 9, 2002)
tulip0: EEPROM default media type 10baseT.
tulip0: Index #0 - Media 10baseT (#0) described by a 21140 non-MII (0) block.
tulip0: Index #1 - Media 100baseTx (#3) described by a 21140 non-MII (0) block.
tulip0: Index #2 - Media 10baseT-FDX (#4) described by a 21140 non-MII (0) block.
tulip0: Index #3 - Media 100baseTx-FDX (#5) described by a 21140 non-MII (0) block.
tulip0: MII transceiver #1 config 3100 status 786b advertising 01e1.
eth0: Digital DS21140 Tulip rev 34 at 0xc2800000, 00:00:94:7A:C2:7B, IRQ 10.
eth0: Using EEPROM-set media 10baseT.
eth0: Setting full-duplex based on MII#1 link partner capability of 45e1.
mii-tool
eth0: negotiated 100baseTx-FD, link ok
registers for MII PHY 1:
3100 786f 2000 5c01 01e1 45e1 0001 0000
0000 0000 0000 0000 0000 0000 0000 0000
0000 0000 0000 0003 0000 0000 0001 8060
8020 0ca1 0000 1800 a3b9 007b 0005 001b
product info: National DP83840A rev 1
basic mode: autonegotiation enabled
basic status: autonegotiation complete, link ok
capabilities: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
advertising: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD
link partner: 100baseTx-FD 100baseTx-HD 10baseT-FD 10baseT-HD flow-control
lspci
00:0b.0 Ethernet controller: Digital Equipment Corporation DECchip 21140 [FasterNet] (rev 22)
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (5000ns min, 10000ns max), cache line size 08
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at dc00 [size=128]
Region 1: Memory at efffef80 (32-bit, non-prefetchable) [size=128]
Expansion ROM at eff80000 [disabled] [size=256K]
01:01.0 Class 0200: 1011:0009 (rev 22)
00: 11 10 09 00 17 00 80 02 22 00 00 02 08 20 00 00
10: 01 d8 00 00 00 00 80 e5 00 00 00 00 00 00 00 00
20: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 14 28
|