|
OpenBoot PROM
Bootmode is 0
[New I2C DIMM address]
MCR0 = 36a0bc04
MCR1 = c0804000
MCR2 = 7f0ffbb
MCR3 = 3ff
Ecache Size = 256 KB
NVRAM Test
Icache Test
Dcache Test
MMU Test
FPU Test
Ecache Tag Addr Test
Ecache RAM Addr Test
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0x60000000
MEMSIZE=0x20000000
Data Line Test
Core Memory Test
Clearing memory...including Unix retained memory...Done
Turning ON MMUs Done
Copy ROM to RAM (170080 bytes) Done
Orig PC=0x1fff0007e44 New PC=0xf0f07e9c
Processor Speed=500MHz
Memory Data Line Test
Memory Addr Line w/ Ecache Test
ECC Block Memory Test
Looking for Dropin cPOST ... found
Copying Client...Done
Transferring control to Client...
Sun Microsystems, Inc. cPOST
@(#) cpost 1.0.17 2003/10/06 17:10
All Basic UltraSPARC IIe PBM Tests
Init CPU PBM
PIO Decoder And BCT Test
CPU IOMMU Reg Test
CPU IOMMU RAM NTA Test
CPU IOMMU CAM NTA Test
CPU IOMMU RAM Address Test
CPU IOMMU CAM Address Test
IOMMU TLB Compare Test
IOMMU TLB Flush Test
PBM Control/Status Reg Test
PBM Diag Reg Test
CPU PBM Reg Test
All Basic APB Simba Tests
Init PCI
All Basic RIO Tests (RIO# 1)
RIO Ebus Config Space Reg Test
RIO Network Config Space Reg Test
RIO Firewire Config Space Reg Test
RIO USB Config Space Reg Test
All Basic RIO Tests (RIO# 2)
RIO Ebus Config Space Reg Test
RIO Network Config Space Reg Test
RIO Firewire Config Space Reg Test
RIO USB Config Space Reg Test
All Basic SCSI Controller Tests
Symbios SCSI Controller PCI Config Space Test
All Basic SCSI Controller Tests
Symbios SCSI Controller PCI Config Space Test
Basic SouthBridge Tests
Southbridge ISA Config Space Reg Test
Southbridge PMU Config Space Reg Test
Southbridge IDE Config Space Reg Test
Southbridge Audio Config Space Reg Test
All Memory Stress Tests
Consist Write Data Test
Resetting...
Processor Speed = 500 MHz
Baud rate is 9600
8 Data bits, 1 stop bits, no parity (configured from lom)
Firmware CORE Sun Microsystems, Inc.
@(#) core 1.0.17 2003/10/06 17:09
Software Power ON
Verifying NVRAM...Done
Bootmode is 0
[New I2C DIMM address]
MCR0 = 36a0bc04
MCR1 = c0804000
MCR2 = 7f0ffbb
MCR3 = 3ff
Ecache Size = 256 KB
Clearing E$ Tags Done
Clearing I/D TLBs Done
Probing memory
Done
MEMBASE=0x60000000
MEMSIZE=0x20000000
Clearing memory...Done
Turning ON MMUs Done
Copy ROM to RAM (170080 bytes) Done
Orig PC=0x1fff0007e44 New PC=0xf0f07e9c
Processor Speed=500MHz
Looking for Dropin FVM ... found
Decompressing Client Done
Transferring control to Client...
ttya initialized
Reset Control: BXIR:0 BPOR:0 SXIR:0 SPOR:1 POR:0
Probing upa at 1f,0 pci pci pci
Probing upa at 0,0 SUNW,UltraSPARC-IIe SUNW,UltraSPARC-IIe (256 Kb)
Loading Support Packages: kbd-translator
Loading onboard drivers: ebus flashprom eeprom idprom SUNW,lomh
Probing /pci@1,1 Device 3 pmu i2c temperature dimm dimm dimm dimm
i2c-nvram idprom motherboard-fru fan-control
lomp
Netra T1 200 (UltraSPARC-IIe 500MHz), No Keyboard
OpenBoot 4.0, 1536 MB memory installed, Serial #XXXXXXXX.
Ethernet address XX:XX:XX:XX:XX:XX, Host ID: XXXXXXXX.
ok .speed
CPU Speed : 500.00 MHz
Primary PCI : 66 Mhz
PCI Bus A : 33 MHz
PCI Bus B : 33 MHz
Memory Speed : 100.00 MHz ( CPU:SDRAM = 5:1 )
ok show-devs
/SUNW,UltraSPARC-IIe@0,0
/pci@1f,0
/virtual-memory
/memory@0,0
/aliases
/options
/openprom
/chosen
/packages
/pci@1f,0/pci@1
/pci@1f,0/pci@1,1
/pci@1f,0/pci@1/scsi@8,1
/pci@1f,0/pci@1/scsi@8
/pci@1f,0/pci@1/scsi@8,1/tape
/pci@1f,0/pci@1/scsi@8,1/disk
/pci@1f,0/pci@1/scsi@8/tape
/pci@1f,0/pci@1/scsi@8/disk
/pci@1f,0/pci@1,1/usb@5,3
/pci@1f,0/pci@1,1/network@5,1
/pci@1f,0/pci@1,1/ide@d
/pci@1f,0/pci@1,1/usb@c,3
/pci@1f,0/pci@1,1/network@c,1
ok probe-scsi
Target 0
Unit 0 Disk SEAGATE ST373405LC 0002
Target 1
Unit 0 Disk SEAGATE ST373405LC 0002
|